 |
|
 |
 |
|
|
SAS-121 |
|
 |
Home
|
SAS-121
Select-a-Seal®/Rubber Edged Composite Gasket
|
|
|
| SAS-121 combines a medium density fiber carrier with a styrene butadiene rubber sealing bead. It is used for sealing water and coolant mixtures in applications that require the carrier to conform to irregular flange surfaces. It is intended for continuous service at temperatures up to 135oC (275oF).
|
|
|
 |
|
Carrier Material |
SAS-1 |
|
|
General Description of Carrier |
Medium density, nitrile butadiene bound material with reinforced cellulose fiber. |
|
|
Caliper, mm(inch) |
0.8, 1.0 (0.031, 0.039) |
ASTM F 104 |
|
Density, g/cc(lb/cu.ft) |
1.20 (75) (min.) |
ASTM F 1315 |
|
Compressibility, % (at 34.5MPa) |
15 - 30 |
ASTM F 36 |
|
Recovery, % |
35 (min.) |
ASTM F 36 |
|
Tensile Strength, AMD, MPa(psi) |
11.03 (1600) (min.) |
ASTM F 152 |
|
|
|
Polymer Edge |
SAS-21 |
|
|
General Description of Polymer |
Styrene Butadiene Rubber Blend, generally used for water and coolant applications. |
|
|
ASTM Classification |
M1CA503 |
ASTM D 2000 |
|
Temperature Rating, oC(oF) |
125 (257) |
ASTM D 2000 |
|
Durometer Hardness, Type A |
45 - 55 |
ASTM D 2240 |
|
Tensile Strength, Initial, MPa(psi) |
3 (435) (min.) |
ASTM D 412 |
|
Edge Height |
Specified on part drawing. |
ISI M10.4X102 |
|
|
|
| Carrier specification values determined by the test methods required for ASTM F-104, Type 7 materials. Carrier is available with release coating per ISS 123316. Carrier caliper and release coating, and polymer edge height are specified on part drawing. |
|
|
|
EnCore, Hydro-Fused, Pro-Formance, Select-a-Seal, Syntheseal, Thermo-Tork, and Voltoid are registered trademarks of Interface Solutions, Inc. MicroPore is a trademark of Interface Solutions, Inc.
WARNING: The description and performance data provided herein constitute a material specification for quality control purposes, but do not imply suitability for use in a specific application. Your specific application should not be undertaken without independent study and evaluation for suitability. Failure to select proper sealing products may result in either property damage or personal injury. For specific application recommendations, contact Interface Solutions. INTERFACE SOLUTIONS EXPRESSLY DISCLAIMS ALL WARRANTIES EITHER EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL ISI BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THE INFORMATION CONTAINED IN ITS SPECIFICATION DATA SHEETS, ITS PRODUCTS OR THEIR FUTURE USE BY YOU OR ANY THIRD PARTIES, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
| |
Interface Sealing Solutions
22260 Haggerty Road , Suite 200
Northville, MI 48167
|
|
Tel: (248) 596-2800
Fax: (248) 596-2880
|
|
|
Previous Revision Date: 05-19-2006
Latest Revision Date: 02-06-2007
|
|
 |
 |
|
|
|
